Supports up to 735kbps wireless link rate.
Supports Point-to-Point, Point-to-Multipoint, Multipoint-to-Point and Mesh topologies.
Supports maximum 1024 nodes mesh network.
High sensitivity: -114 dBm when data rate is 125kHz.
Supports frequency hopping(FHSS).
Air-to-ground LOS(light of sight) distance: ≥300km,ground-to-ground LOS range 3~10km.
Two serial ports (TTL/RS232/RS422 optional).

Mesh Radio Overview:

The Mesh radio enables decentralized and long-distance communication among a large number of nodes. All nodes can communicate independently without interfering with each other.
Support large-scale dense node access to wireless transmission, dynamic networking and flexible reorganization.
Support full-multiplexing communication,the node can send data while also receiving data from all other nodes, and there is no mutual interference.
And in the case of absence of the center, it can achieve interoperability between any node and all other nodes in the network without mutual interference.
In the absence of a central node, it is capable of establishing connections between any node in the network and all other nodes.

Application of the Mesh Radio:

Our Mesh radio device are mostly used in swarming drones, Internet of Things, UAV data link, remote control, data collection, artificial intelligence, military equipment, etc.

HNC2 20W data link mesh radio models:

Model	RF Power	Network Scale	Frequency Bands
HNC2-H400-20W	20W	Max. 1024 nodes, up to 16 hops	430~450MHz
HNC2-H800-20W			820~854MHz
HNC2-H900-20W			900~940MHz

HNC2-F400-20W	20W	Max. 256 nodes, up to 3 hops	430~450MHz
HNC2-F800-20W			820~854MHz
HNC2-F900-20W			900~940MHz

Technical Specifications:

IP Mesh Radio Link With 20W RF Power And 300km Long Range Data Transmission
Frequency	Different models support different frequency bands, see above models table
Bandwidths	1MHz/500kHz/250kHz/125kHz selectable
Number of nodes and hops	Maximum 1024 nodes up to 16 hops or 256 nodes up to 3 hops, see models table
Frequency hopping speed:	1MHz:Over 1800 times per second 500kHz:Over 900 times per second 250kHz:Over 450 times per second 125kHz:Over 225 times per second
Effective data rate	1MHz: Up to 735kbps 500kHz:Up to 370kbps 250kHz: Up to 185kbps 125kHz: Up to 92kbps
Full-multiplexing communication	Support
Air-to-ground LOS(light of sight) distance	≥300km
Centerless self-organized network	Support centerless self-organized network, any node of the network is destroyed without affecting the communication;
Network construction time	Within 1 second
Wireless transmission delay	Minimum 2ms
Dynamic topology	Support dynamic topology, support node joining and leaving, network topology change and deformation can be normal communication;
RF power	20W(43dBm)
Sensitivity	125kHz:-114dBm 250kHz: -111dBm 500kHz:-108dBm 1MHz:-105dBm
Frequency stability	≤1ppm
Modulation	QPSK modulation LDPC coding
Encryption	128-bit encryption
Low power consumption((varies by data rate)	Less than 1.5W(0.06A/24V) when receiving, transmission power consumption (B is in bytes): 1.2KB/s: 2.4W(0.1A@24V) 3.4KB/s: 3.9W(0.16A@24V); 6.4KB/s: 5.5W(0.23A@24V); 12KB/s: 9.6W(0.4A@24V); 26KB/s: 19.2W(0.8A@24V); 37KB/s: 24W(1A@24V); 48KB/s: 32W(1.35A@24V).
Operating voltage	24V as default, supports a wide voltage input of 7-36V. Transmission power varies with voltage: 7V:2W 12V:5W 18V:10W 24V:20W 20-36V:20W-30W Power supply capacity requirement: ≥2.5A @ 24V (20W)
Operating temperature	-40～+55°C
Dimensions	83.85316mm
Weight	91.3g

Input/ Output

I/O	Description
Power-in	Power-input, XT30PW-M connector
Dip-switch	Dial switch, switch between configuration mode and transparent transmission mode
Uart 1	Configure/transparent data serial port 1, TTL 3.3V level as default,optional RS232 or RS422 serial port
Uart 2	Transparent data serial port 2, TTL 3.3V level as default,optional RS232 or RS422 serial port
ANT	SMA female, antenna port, the required antenna impedance is 50Ω
PWR-LED	Red, power input status indicator led, continuous light on when power input is normal
RX-LED	Green, data receiving indicator led, briefly lit during power on self-test, light on when receiving data
TX-LED	Green, data transmitting indicator led, briefly lit during power on self-test, light on when transmitting data
CA-LED	Blue, interference indicator led, briefly lit during power on self-test, frequently lit in configuration mode. In transparent transmission mode: When the light is on, there is interference with the air interface, and the brighter the light, the stronger the interference.

Inquiry Cart 0