Hincn Limited
Hincn Limited
Add to Cart
25W RF Power Amplifier For Time Division Synchronous Frequency Data Transmission
Technical Specifications:
| Model number | HCTD6090-25 |
| Frequency range | 402~480MHz, 908~928MHz(more frequencies available) |
| Working Voltage | 12~18V(built-in 12V low-dropout voltage regulator) |
| Working current | 5.0～5.9A@12.5～18V |
| Output Power | ≥25W |
| Transmitting Gain | ≥16 ± 1dB (10~50dB can be customized) |
| Flatness In Band | ≤ ±0.5 dB(typical value±0.25dB) |
| Receiving Gain | ≤16dB±2dB |
| Maximum input power | 31dBm |
| Input VSWR | ≤2 (load 50Ω) |
| Output VSWR | ≤1.5 (load 50Ω) |
| RF switch switching time | On-time ≤ 5us / Off-time ≤ 1us |
| Power amplifier transmit-receive isolation | ≥ 45 dB (typical value: 48 - 58 dB) |
| Reliability | Amplifier would not be damaged without antenna |
| Delay | less than 20 uS |
| RF connector | SMA or MCX |
| Working temperature | -25~+85℃ |
| Size | 60*90*15mm (not including the radiator and connector) |
| Weight | 140g |
Control Level: Automatic, which automatically detects the input power level to achieve automatic transmission and reception. The transmission starts when the input power reaches 22 dBm, and it switches to reception when it drops below 10 dBm (or the "EN" terminal can be externally connected to achieve TTL high-level transmission and low-level reception).
EN 1: Power amplifier transmission state, reception off;
EN 0: Reception state, transmission off (the static current of the power amplifier is less than 0.15A)
Drawing of the TDD power amplifier module:
Port Description:
1. Since the data transmission radio uses the same port for transmission and reception, so the ‘RX’ port of this TDD power amplifier module is left unused. The 'TX' port is the RF port of the data transmission radio, and the ‘ANT’ port is connected to the filter to the antenna.
2. 'EN' or 'EN-TR' is the transmission enable mode of the data transmission radio in non-automatic mode. (in automatic mode and enable mode, it needs to be set at factory, with 1.8~5V TTL level).
3. '+12V' or 'VDC' is +12~18V power supply. The wire pin pressed by this inductive capacitor is the negative pole.
4. 'FULL' blue indicator light indicates full power output indication. When the output power reaches the ALC trigger and reaches a certain depth, this LED indicator light will light up.
5. 'TX' red indicator light indicates transmission state.
6. 'RX' green indicator light indicates reception state.
7. 'EN-PWR' terminal is only available in the old version. In the new version, it is generally connected to 12~18V, while '+12V' may be based on the high-power 80W version and connected to 24~28V.
8. 'FWD' is a backup power detection output terminal. It is usually left empty and can be modified to be a 12V or 28V power input as needed.
Frequently Asked Questions:
Q1. Can you make the RF Power Amplifier to be other frequencies? Output 10W and more?
A:Yes, under certain circumstances,in order to achieve long-distance transmission, high power output and high efficiency. It can output a digital power of 10W for use.And we also have different power amlifiers with 10W,20W,50W etc.
Q2. How long is the warranty?
A: 1 Year warranty and lifetime maintenance.